WARNING
This body lift kit should only be installed on vehicles that are in
good working condition. Before the installation begins, the
vehicle should be thoroughly inspected for evidence of corrosion
or deformation of the sheet metal around the factory body
mounts. This body lift kit should not be installed on any vehicle
that is suspected to have been in a collision, or misused. Off
road use of you vehicle with this body lift installed may increase
the stress applied to the factory body mounts. It is not
recommended that any vehicle, with a body lift installed, be
involved in any extreme off road maneuvers such as jumping.
Failure to follow this warning may result in serious personal
injury and/or serious damage to your vehicle.
WARNING
Performance Accessories strongly discourages the use of a
suspension lift kit or any other lift device in addition to a body
lift kit. A vehicle that uses a combination of lift devices not
originally engineered to be used together may result in
unexpected and unsafe handling characteristics. Many states now
have laws restricting bumper heights and vehicle lifts. Local
laws should be consulted to determine if the changes you intend
to make to your vehicle complies with state laws.
INSTALLATION INSTRUCTIONS
98 NISSAN FRONTIER 2 WD
KIT # 4073
WARNING
WARNING
The installation of larger wheel and tire combinations may
reduce the effectiveness of the Anti-lock Braking System.
Installation of a Performance Accessories body lift will change
the center of gravity and the handling characteristics of the
vehicle. Because of the higher center of gravity and larger tires,
the vehicle will handle and react differently both on and off road.
You must drive it safely! Extreme care must be taken to prevent
vehicle rollover or loss of control, which could result in serious
injury or death. Avoid sudden sharp turns or abrupt maneuvers
and always make sure all vehicle occupants have their seat belts
fastened.
NOTE
Performance Accessories recommends using the Loctite®
supplied in the kit, on all hardware unless noted in the
instructions.
WARNING
Always wear eye protection when operating power tools.
WARNING
Read and understand all instructions, warnings, cautions, and
notes in this sheet and in your owners manual before you begin
the installation of this body lift kit.
1. Read all warnings and instructions completely and carefully
before you begin. Check the kit for proper contents (refer to the
part’s list and the picture diagrams). Only attempt to install this
kit on the vehicle described above. If anytime during the
installation you encounter something different from what is
outlined in the instructions, call technical support. (520) 636-
0979.
CAUTION
Proper installation of a Performance Accessories body lift kit
requires knowledge of the factory recommended procedures for
disassembly an assembly of original equipment components. It is
recommended that the factory shop manual and any special tools
necessary to your vehicle be on hand during the installation.
Installation of this body lift kit without proper knowledge of the
factory recommended procedures may affect the performance of
these components and the safety of you vehicle. It is strongly
recommended that a certified mechanic who is familiar with the
installation of similar components install this body lift kit.
WARNING
Make sure that your vehicle is properly blocked and secured
before you begin installation of this lift kit.
2. Park the vehicle on a clean, dry, flat, level surface. Block the
tires so the vehicle cannot roll in either direction.
bushing, the frame perch, the stock top bushing, the block, and
threading into the nut that is captured inside the body. Reinstall
the two bolts that mount the outside support bracket to the
bottom of the frame perch. Do not tighten any of the bolts at this
time.
WARNING
Use extreme caution when working near fuel lines and fuel tank.
Clean up spilled fuel immediately. Any spark could cause an
explosion or fire resulting in serious personal and property
damage.
22. Repeat step #21 for the driver’s side of the cab. Adjust the
cab to bed clearance. Install the outside support plates to the cab
using the stock bolts. Attach the outside support plates to the
stock outside support brackets using two 7/16” x 1” bolts, four
7/16” SAE washers, and two 7/16” nylock nuts on each side of
the cab. Do not tighten the cab-mounting bolts at this time.
18. Remove the screws that mount the fuel filler neck to the
body. Loosen the hose clamp that mounts the filler hose to the
fuel tank. Loosen the clamp that mounts the large vent hose to
the tank. There are two other hoses attached to the filler neck.
They are attached to a small box on top of the filler neck.
Looking at the filler neck from the outside of the vehicle, detach
the hose on the right from the filler neck. It will be reattached
after the lifting operation is complete. Remove the hose on the
left from the fuel tank. Remove the entire filler neck and hose
assembly from the vehicle.
23. Loosen, but do not remove all six bed-mounting bolts.
Remove the mounting bolts from the passenger side of the bed
only. Using a hydraulic jack and a wooden block slowly lift the
passenger side of the bed just high enough to place the spacer
blocks on the frame. Install the new mounting bolts in the
following positions; ½ x 5” at the front bed mount, ½” x 4 ½” at
the middle bed mount, and ½ x 5 1/2" at the rear bed mount. The
bolts should have a ½” USS (large) washer installed, then the
bolt should be inserted through the thick rubber bushing, through
the frame, through the thin rubber bushing, through the spacer,
and through the bottom support rail of the bed. Install a ½” USS
washer and nylock nut on each bolt. Do not tighten at this time.
19. Disconnect the license plate lights from the rear bumper.
Remove the six bolts that mount the rear bumper to the frame.
Remove the bumper from the vehicle.
20. Measure the distance between the cab and the bed. Record
this measurement to insure proper alignment of the cab and bed
after the lifting operation has been completed. Remove the bolts
at the rear cab mount that mount the body to the side of the rear
cab mount. There are two bolts inserted from the inside of the
frame mount and are threaded into the body. There are two more
bolts that are inserted from the bottom and thread into the
mounting pad. When the rear cab bolt is removed, the bracket
can be removed. Loosen, but do not remove all six cab-mounting
bolts. They are located as follows; in the front fender well, in the
front floorboard, and at the rear of the cab screwing up into the
cab. The front two mounting bolts are installed from the top and
the rear bolt is installed from the bottom.
24. Repeat step # 23 for the driver’s side of the bed. Realign the
bed to the cab. Refer to the measurements made earlier. One by
one remove each body-mounting bolt. Apply the loctite®
adhesive to the bolt according to the loctite® application
instructions. Tighten each body mounting bolt to vehicle torque
specifications. Refer to vehicle service manual for torque
specifications. Repeat this step for all cab and bed mounting
bolts.
WARNING
WARNING
Failure to install the steering extension properly could result in
loss of steering causing damage to the vehicle and possible
personal injury.
Failure to replace the OEM body mounting hardware (except
mounting bolts) in the stock locations could result in damage to
the vehicle and possible personal injury.
25. Install the steering extension into the lower coupler of the
steering shaft. Be sure that the extension is installed so the
mounting bolt will slide across the flat on the steering extension.
Install the stock retaining bolt in the steering shaft. If the bolt
will not easily slide across the flat on the steering extension, the
extension has been installed incorrectly. Do not tighten the
retaining bolt at this time. Extend the mark on the lower part of
the steering shaft down onto the extension. Install the upper part
of the steering shaft into the upper coupler inside the engine
compartment. Be sure to align the marks made earlier. Install the
stock retaining bolt in the upper coupler. Align the mark on the
steering extension with the mark on the gearbox. Install the
steering extension on the gearbox splined shaft. Install the
retaining bolt in the steering extension. Do not tighten the
retaining bolt at this time. Be sure that all marks are properly
aligned and that there is ample engagement at all unions. Apply
the loctite® adhesive to the bolt according to the loctite®
application instructions. Tighten all steering hardware securely.
21. Using a hydraulic jack and a wooden block, slowly lift the
passenger side of the cab just high enough to put the spacers on
the mounting pads. Continually check for any hoses, wires, etc.
to be sure that everything is flexing properly and not binding. Be
especially careful of the a/c hose at the firewall and the at the
core support. Place the spacer block on top of the mounting pad.
Using a 3/8" washer in conjunction with the stock washer, install
the 7/16" x 7" bolts at the front two mounts (core support and
front floorboard) and the 10mm x 180mm bolt at the rear cab
mount. For the front two mounts, the 3/8” washer should be
installed on the bolt. The bolt should then be inserted from the
top through the stock top washer, through the body, the spacer,
the factory top bushing, the frame perch, the bottom factory
bushing, the stock bottom washer and inserted into the 7/16”
nylock nut provided with the kit. The 3/8” washer should be
installed on the 10mm bolt, the bolt should be inserted from the
bottom through the outside support bracket, the bottom stock
We recommend the use of loctite or a similar adhesive on all
steering hardware.
enough slack in the line to remount it to the core support. If there
is not enough slack, carefully bend the line to gain more slack.
Be sure that there is ample slack in the line. Install the bolt that
mounts the a/c line to the core support. Tighten securely.
26. Using the new lower radiator support as a template, Mark the
lower core support for alignment of the new support. Align the
holes in the new bracket with the stock mounting holes. Mark the
core support for proper alignment of the new support after the
stock mount has been removed. Using a die grinder or hacksaw
cut away the bottom radiator mount from the core support. Be
especially careful of the a/c condenser when cutting the sheet
metal. Cut to the outside of each mounting hole approximately 1
½” to 2” and flush with the vertical surface of the core support
(allow enough room for the radiator to slide past the remaining
sheet metal without hitting). Place the new lower radiator
support bracket on the core support. Be sure that the bracket is
aligned with the marks made earlier and that the bracket is
positioned flush against the core support with the lip resting on
top of the core support. Using the bracket as a template, mark the
top of the core support through the holes in the bracket. Remove
the bracket. Drill a ¼” hole at both locations. Mount the bracket
to the core support by install a ¼” x 1” bolt with a ¼” washer
through the bracket, and the core support. Install a ¼” washer
and nylock nut on the bolt from the bottom of the core support.
Tighten the ¼” hardware securely.
31. Disconnect the vacuum that runs between the bottom of the
intake and the cruise control mechanism on the passenger side
fender well. Cut the hose approximately in the middle. Install the
3" long hose extension between the two pieces of the hose.
Install two #6 hose clamps to hold the extension in place.
Tighten securely. Reinstall the hose to the bottom of the intake
and to the cruise control mechanism.
32. Reroute the hose that was connected to the vacuum module
in front of the cruise control. Reroute the hose on the other side
of the steel lines that comes up from the frame. This will give
enough slack to reconnect to the vacuum module. It may be
necessary to carefully bend the steel portion of the line to route it
properly.
33. Reconnect the engine to body ground wire to the body. The
ground wire can be reconnected to the lower of the two holes in
the bell housing area. Tighten the mounting bolt securely.
34. Mount the parking brake cable-relocating bracket to the
stock bracket using two 5/16 x 1" bolts, four 5/16" USS washers,
and two 5/16" nylock nuts. Mount the parking brake cable to the
new bracket using the stock bolt. Remount the two brackets that
hold the cable to the bell housing. Tighten all parking brake
hardware securely. We recommend the use of loctite or a similar
adhesive on mounting hardware.
27. Install the radiator on the new lower support bracket.
Remove the two rubber bushings from the plastic studs on the
top of the radiator. Install the rubber bushings into the large hole
in the 2” x 3” x 1” rectangular tube. Slide the tube with the
rubber bushing onto the studs at the top of the radiator. Reinstall
the stock upper radiator mount. The hole in the stock mount
should align with the hole in the tube. Mount the tube to the
stock bracket using a 3/8” bolt, two 3/8” USS washers, and a
3/8” nylock nut on each side. Do not tighten at this time. Be sure
that the radiator is secure. Tighten all radiator mounting
hardware securely. Install the fan shroud to the radiator using the
stock hardware. Check the fan to fan shroud clearance. Be sure
that the fan cannot make contact with the shroud. Tighten the fan
shroud mounting hardware securely. Install both radiator hoses
to the radiator. Tighten the hose clamps securely.
35. Using two 10mm – 1.25 x100 bolts with a 3/8” washer on
each bolt, and the two 3” long tubes mount the cab safety loop to
its original location. It may be necessary to bend the loop slightly
to align the loop to the mounting holes with the spacer tubes
installed. Apply the loctite® adhesive to the bolts according to
the loctite® application instructions. Tighten safety loop
mounting bolts securely.
WARNING
28. Reconnect the upper heater hose to the heater core at the
firewall. It may be necessary to remove the tie wrap around both
hoses to gain enough slack to reconnect the upper hose. The
lower heater hose needs to be lengthened. Cut the hose below the
top bend. Install the 4" heater hose extension. Fasten using two
#10 hose clamps. Install the heater hose to the heater core at the
firewall. Tighten all heater hose clamps securely. Refill the
cooling system as much as possible at this time. It will need to be
topped off after the vehicle has been started.
Use extreme caution when working near fuel lines and fuel tank.
Clean up spilled fuel immediately. Any spark could cause an
explosion or fire resulting in serious personal and property
damage.
36. Lengthen the fuel filler hose. Cut the filler hose toward the
bottom below the first bend. Install the 1 3/4" fuel filler
extension between the two sections of the filler hose. Install a
#28 hose clamp at each end of the extension. Tighten both hose
clamps securely. Remove the large vent hose from the filler
neck. Install the new vent hose to the filler neck vent. Install a
#10 hose clamp and tighten securely. Remove the small hose
attached to the left nipple of the box on the filler neck. Replace it
with the 1/4" hose provided in the kit. Install a #6 hose clamp
and tighten securely. Install the filler assembly in the vehicle.
Using the stock clamp, reconnect the filler hose to the fuel tank.
Using a #10 hose clamp, reconnect the large vent hose to the fuel
29. Reroute the vacuum brake booster hose over the a/c hose at
the firewall. Bend the bracket that mounts the a/c hose to the
firewall forward to a 45-degree angle. This should give the hose
ample slack. Reconnect the hose to the brake booster. If the line
still feels tight, it may be necessary to carefully bend the steel
portion of the line to gain more slack in the line.
30. Check the a/c line at the core support. Be sure that there is
tank. Using a #6 hose clamp, attach the small hose to the fuel
tank. Reconnect the remaining small hose to the filler neck.
Tighten all hose clamps securely. Install the screws that mount
the filler neck to the body. Tighten securely. Replace the fuel
cap.
WARNING
Raising the rear bumper is intended to enhance the appearance of
the vehicle only. The rear bumper will no longer be rated for
towing of any kind. Attempting to tow with the rear bumper
after it has been raised can result in damage to the vehicle and
possible personal injury. A class III receiver hitch must be
installed in order to tow with the vehicle after the rear bumper
has been raised.
37. Lengthen the transmission shift lever. Scribe a line along the
shift lever below the bend. Be extremely careful during this
procedure to not damage any of the parts that are attached to the
shift levers. Cut the lever into two pieces through the line. Insert
the shift lever extension between the two parts of the shift lever.
The tapered end of the extension goes toward the bottom. Both
parts of the shift lever should slide into each end of extension.
Be sure that the lever is all the way in the extension. Using the
holes in the extension as a guide, mark the shift lever for drilling.
Drill a 1/8” hole through each part of the shift lever. Reinstall the
shift lever into the extension. Align the holes in the extension
with the holes in the shift lever. Install a 1/8” x ¾” roll pin at
both ends of the extension.
42. Install the rear bumper. If you wish to tow with the rear
bumper, reinstall the bumper in the stock location using the stock
brackets and mounting hardware. To raise the rear bumper,
remove the two bolts that mount each rear bumper bracket to the
bumper. Drill a new mounting hole in the bumper side of the
stock bumper bracket according to the diagram. Hold the bumper
bracket against the frame in the stock location. Pivot the rear of
the bracket upward until the last hole on the bracket is aligned
with the bottom of the slotted hole in the frame. The first hole in
the bracket should still align with the last stock hole in the
bumper. The center mount hole should also align with a hole in
the frame. Mount the brackets to the frame using the 7/16” x 1”
bolts, 7/16’ USS washers, and 7/16” nylock nuts provided. Do
not tighten. Mount the bumper to the holes specified in the
diagram using the 7/16” x 1” bolts, 7/16’ USS washers, and
7/16” nylock nuts provided. The rear bumper should align with
body. Adjust the bumper to body clearance. Tighten all bumper-
mounting hardware securely. We recommend the use of loctite or
a similar adhesive on all mounting hardware. Reconnect the
license plate lights to the bumper.
38. Replace the shift lever in the vehicle. Insert the transmission
shift lever into the top of the transmission. Be sure that it is all
the way in replace the cover. Install the spacer shim. Install the
retaining clip. Check the shift lever operation. Be sure that there
is complete engagement in all gears. Replace the shift boot and
housing assembly. Tighten all mounting screws securely. Check
the shift lever operation again.
39. Replace the carpet and matting to its original position.
Replace both kick panels and both doorjamb scuff plates.
Tighten the mounting screws securely.
43. Reinstall the air cleaner. If the vehicle is equipped with a/c,
the back right corner of the housing must be notched to clear the
a/c line at the firewall. Trim the bottom of the housing just to the
left of the corner just enough for the a/c line to clear. Install the
bottom part of the housing. Reconnect all houses that were
disconnected at the beginning of the installation. Trail fit the top
of the housing. Mark the top where it makes contact with the a/c
line. Notch this section of the top housing. Install the top of the
housing. Install the air intake duct to the upper radiator mounting
brackets. Install the mounting screws and tighten securely.
40. Using the stock bolts, mount the front bumper brackets to
the frame. Tighten the mounting bolts so the brackets cannot
move, but so the bumper can still be adjusted. Slide the front
bumper onto the relocating brackets. Align the holes in the stock
bumper brackets with the holes in the new bumper brackets. The
rear leg of the stock bracket will need to be trimmed to clear the
bend in the bracket. Mark the bottom of the rear leg where it
contacts the bend on the new bracket. The bottom valance will
need to be notched around the frame horns. Mark the valance
around the frame horns. Remove the bumper from the vehicle.
Trim the rear leg on the stock bumper brackets. The cut should
go through the bottom of the mounting hole. Notch the valance
to clear the frame horns. Reinstall the bumper on the vehicle.
Mount the bumper to the relocating brackets using two 7/16” x
1" bolts, four 7/16” USS (large) washers, and two 7/16" nylock
nuts. Adjust the bumper to body clearance. Tighten all bumper-
mounting hardware securely. We recommend the use of loctite or
a similar adhesive on all mounting hardware. Reconnect the
wires to the driving lights.
WARNING
All welding should be performed by a certified welder only.
44. Install the four bed overload pads on the frame over in the
wheel wells. There should be two places on each side where the
bed rested on the frame, but was not mounted to the frame. This
is where the overload pads go. The pads need to be tack welded
to the frame only.
41. Reinstall the grill to the core support. Tighten all mounting
screws securely.
45. Reconnect both battery cables. Be sure to reconnect the
positive cable first, then the negative cable. Reinstall the airbag
fuse if equipped.
46. Place the warning sticker on the dash in plain sight of all
vehicle occupants.
thoroughly. Test-drive the vehicle in all gears and 4 wheel drive
ranges. Pay very close attention to all vehicle systems. Check all
hardware again in 500 miles and as part of your regular
maintenance schedule.
CAUTION
All fasteners should be retorqued after 500 miles and after off
road use. All body lift components should be visually inspected
and fasteners retorqued during routine vehicle servicing.
CAUTION
47. Double-check the vehicle. Check all mounting hardware to
be sure that it is properly tightened. Check all wires, hoses,
cables, etc. to be sure that there is ample slack. Check the vehicle
electrical system. Start the vehicle. Check the steering in both
directions to be sure that there is no bind. Check clutch
operation. Check the operation of the brake system and the
parking brake. Check both shift levers’ operation. Be sure that
there is proper engagement in all gears and 4 wheel drive ranges.
Check coolant level. Caution: never open a closed cooling
system after the vehicle has been started. Only fill the cooling
system if the cap has been removed while the vehicle was still
cold. Fill the coolant to the proper level. Reinstall the radiator
cap. Carefully check all hoses to be certain that they have been
connected properly and that there is ample slack. With the
amount of hoses on this vehicle, it is vital that this be checked
Performance Accessories does not recommend any particular
wheel and tire combinations for use with its body lifts and can
not assume responsibility for the customers choice of wheels and
tires. Your owner's manual can be referenced for recommended
tire sizes and warnings related to the use of oversized tires.
Larger wheel and tire combinations increase stress and wear on
steering and suspension components, which leads to increased
maintenance and higher risk for component failure. Larger
wheel and tire combinations also alter speedometer calibration,
braking effectiveness, center of gravity, and handling
characteristics. Consult with an experienced local off road shop
to find what wheel and tire combinations work best with your
vehicle.
NOTE
All warranty information, instruction sheets, and other documents regarding the installation of this product must be retained by the
vehicle owner. Information contained in the instructions and on the warranty card will be required for any warranty claims. The vehicle
owner needs to understand the modifications that have been made to his vehicle and how they affect the handling and performance of the
vehicle. Failure to provide the customer with this information can result in damage to the vehicle and possible personal injury.
PARTS LIST
4 #6 hose clamps
2 #10 hose clamps
2 #28 hose clamps
Kit
1 Transmission shifter extension bracket
2 Front bumper brackets
1 Lower radiator support bracket
1 Parking brake cable relocation bracket
2 Outside cab support brackets
1 1 3/4" x 3" fuel-filler extension
1 1/2" x 19" fuel vent hose
1 1/4" x 17" fuel vent hose
1 Warning to driver sticker
1 Logo label
2 3/8" x 3" scd. 40 cab safety strap
1 3/8" x 4" scd. 40 heater hose extension
1 7/16" x 3" .049" vacuum hose extension
2 1/8" x 3/4" roll pins
6 3x3 blocks
6 3x2 blocks
2 2x3 spacers with holes
4 2x3 spacers without holes
1 10ml bottle Loctite 262
1 Bolt pack BP4073
4 7/16" x 7" bolts
2 10mm x 180mm bolts
2 1/2" x 4 1/2" bolts
2 1/2" x 5" bolts
2 1/2" x 5 1/2" bolts
6 Thick 1/2" USS washers
6 1/2" USS washers
6 3/8" SAE washers
4 7/16" nylock nuts
6 1/2" nuts
1 se 9000 steering extension
1 3/8" x 1 1/4" socket head bolt
1 Hardware Pack HP4073
Bolts
16 7/16" x 1" bolts
2 10mm x 100mm bolts
2 3/8" x 1" bolts
2 5/16" x 1" bolts
2 1/4" x 1 " bolts
Washers
8 7/16" SAE washers
24 7/16" USS washers
4 3/8" SAE washers
4 5/16" USS washers
4 1/4" SAE washers
Nuts
16 7/16" nylock nuts
2 3/8" nylock nuts
2 5/16" nylock nuts
2 1/4" nylock nuts
Miscellaneous
|
Miele Ventilation Hood HS60CIW1 User Manual
Miller Electric Welder S 21E User Manual
National Instruments Network Card NI 9215 User Manual
Nilfisk ALTO Vacuum Cleaner CR 1000 User Manual
Olivetti Printer 16MF User Manual
Omega Oxygen Equipment FL45200A User Manual
Omega Vehicle Security Network Card TCIC User Manual
Panasonic Computer Drive CF VDD285 User Manual
Panasonic Laptop CF M32 Series User Manual
ParaBody Home Gym PBF 472 User Manual